PID/DATA MONITOR TABLE [FRONT BODY CONTROL MODULE (FBCM)]

PID	Unit/Operation	Data contents	Data read/use method	Module control terminal
ABK_CS_BG	Off/On	Note • It is displayed, however, if an accessory part is installed, it cannot be used.
ABK_CS_KEY	Off/On	Note • It is displayed, however, if an accessory part is installed, it cannot be used.
ABK_HD_CS_R	Off/On	Note • It is displayed, however, if an accessory part is installed, it cannot be used.
ABK_HN_CS_R	Off/On	Note • It is displayed, however, if an accessory part is installed, it cannot be used.
ABK_HN_KEY	Off/On	Keyless entry system horn answer-back signal input status • Off: Keyless entry system horn answer-back signal is not received. • On: Keyless entry system horn answer-back signal is received.	Keyless entry system horn answer-back request signal input from rear body control module (RBCM)	• 2I (CAN_L) • 2K (CAN_H)
BAT_TMP^*1	°C, °F	Displays battery temperature (estimated).	Estimated battery temperature transmitted by LIN communication from current sensor	2E (LIN communication)
BG_ALARM_CS^*2	Off/On	Theft-deterrent system alarm signal input status • Off: Hazard warning light flashing request signal is not received • On: Hazard warning light flashing request signal is received	Theft-deterrent system alarm request signal input from rear body control module (RBCM) Note • Operates only if the ignition is switched off.	• 2I (CAN_L) • 2K (CAN_H)
BLWR_MT_RY	Off/On	Blower motor relay output signal status • Off: Blower relay is off. • On: Blower relay is on.	—	2Z (Blower motor relay control)
BRAKE_SW	Off/On	Brake switch operation status • Off: Brake switch (No. 2 signal) is off. (Brake pedal is depressed.) • On: Brake switch (No. 2 signal) is on. (Brake pedal is not depressed.)	Brake switch signal status detected by PCM	• 2N (CAN_L) • 2P (CAN_H)
BRK_F_L_SW	Normal/Low/Reserved/Unknown	Brake fluid level condition • Normal: Brake fluid level is between MAX and MIN. • Low: Brake fluid level is lower than MIN. • Reserved: — • Unknown: Brake fluid level is not determined.	—	2Q (Brake fluid level switch signal)
DCDC_CVT_ST^*3	Wake_Up/Bypass/Boost_1/Boost_2/Boost_3/Error/Default	DC-DC converter status	—	2H (LIN communication)
DCDC_VLT_O^*3	V	Displays DC-DC converter input voltage.	—	2H (LIN communication)
DEFOG_F_CS	Off/On	Front defogger operation request signal from climate control unit • Off: Front defogger control signal is not received. • On: Front defogger control signal is received.	—	• 2I (CAN_L) • 2K (CAN_H)
DEFOG_R_CS	Off/On	Rear defogger operation request signal from climate control unit • Off: Rear window defogger control signal is not received. • On: Rear window defogger control signal is received.	—	• 2I (CAN_L) • 2K (CAN_H)
ENG_C_TMP	°C, °F	Displays the engine coolant temperature value from the PCM.	—	• 2N (CAN_L) • 2P (CAN_H)
ESS_ST	Off/On	Emergency signal system (ESS) operation condition • Off: Emergency signal system (ESS) is not operated. • On: Emergency signal system (ESS) is operated.	—	—
F_FOG_LMP^*4	Off/On	Front fog light control signal • Off: Front fog light is turned off. • On: Front fog light is turned on.	—	—
F_FOG_SW^*4	Off/On	Front fog light switch input signal from start stop unit • Off: Front fog light switch F.FOG signal is not received. • On: Front fog light switch F.FOG signal is received.	—	• 2I (CAN_L) • 2K (CAN_H)
H/L	OFF/DRL/TNS/H/L_LOW/H/L_HI	Headlight control signal • OFF: Headlight is turned off. • DRL: Running light is turned on. • TNS: TNS (parking lights) is turned on. • H/L_LOW: Headlight (LO) is turned on. • H/L_HI: Headlight (HI) is turned on.	—	—
H/L_CLN_RY^*5	Off/On	• Off: Headlight cleaner relay is off. • On: Headlight cleaner relay is on.	—	1Q (Headlight cleaner relay)
H/L_CS_RLS^*6	Off/TNS_On/TNS+H/L_On/TNS+H/L_On_J	Headlight control input signal from auto light sensor/humidity sensor/rain sensor • Off: TNS (parking lights) and headlight on request signal is not received from auto light sensor. • TNS_On: TNS (parking lights) on signal is received from auto light sensor. • TNS+H/L_On: TNS (parking lights) and headlight LO on signal is received from auto light sensor. • TNS+H/L_On_J: —	—	2G (LIN communication)
H/L_HI	Off/On	Headlight HI beams • Off: Headlight HI is turned off. • On: Headlight HI is turned on.	—	—
H/L_SW_HI	Off/On	Light switch position (HI) condition via CAN signal from start stop unit • Off: Light switch HI signal is not received. • On: Light switch HI signal is received.	—	• 2I (CAN_L) • 2K (CAN_H)
H/L_SW_LOW1	Off/On	Displays dimmer switch position of light switch sent from start stop unit via CAN signal • Off: Other than dimmer switch LO position of light switch is received • On: Dimmer switch LO position of light switch is received	Verify if the monitor value switches when the dimmer switch of the light switch is switched between LO and HI positions. If the dimmer switch operation and monitor values do not match, inspect the start stop unit or CAN communication.	• 2I (CAN_L) • 2K (CAN_H)
H/L_SW_OFF	Off/On	Light switch position (OFF) condition via CAN signal from start stop unit • Off: Light switch OFF signal is not received. • On: Light switch OFF signal is received.	—	• 2I (CAN_L) • 2K (CAN_H)
H/L_SW_PASS	Off/On	Light switch position (PASS) condition via CAN signal from start stop unit • Off: Light switch FLASH-TO-PASS signal is not received. • On: Light switch FLASH-TO-PASS signal is received.	—	• 2I (CAN_L) • 2K (CAN_H)
H/L_SW_TNS	Off/On	Light switch position (TNS (parking lights)) status via CAN signal from start stop unit • Off: Light switch TNS (parking lights) signal is not received. • On: Light switch TNS (parking lights) signal is received.	—	• 2I (CAN_L) • 2K (CAN_H)
H/L_TNS	Off/On	Light switch (TNS (parking lights)) output signal • Off: TNS (parking lights) is turned off. • On: TNS (parking lights) is turned on.	—	—
HAZARD_LMP	Off/On	Hazard light output signal • Off: Hazard light is turned off. • On: Hazard light is turned on.	—	—
HAZARD_SW	Off/On/Unknown	Hazard switch input signal from start stop unit • Off: Hazard warning switch is off. • On: Hazard warning switch is on. • Unknown: Hazard warning switch on/off is not determined.	—	• 2I (CAN_L) • 2K (CAN_H)
HBC_CS^*7	Off/On/Invalid	• Off: High beam control (HBC) system signal is not received. • On: High beam control (HBC) system signal is received. • Invalid: High beam control (HBC) system signal has error.	—	• 2I (CAN_L) • 2K (CAN_H)
HBC_ST^*7	Off/On	• Off: High beam control (HBC) system is not operated. • On: High beam control (HBC) system is operated.	—	• 2I (CAN_L) • 2K (CAN_H)
HEAT_CS_R	Off/On	Note • It is displayed, however, if an accessory part is installed, it cannot be used.
IG_ST	Off/On	Ignition switch status • Off: IG1 is off. • On: IG1 is on.	—	—
L_OFF_AUTO^*6	Off/On	Operation status of lights off function by auto-light function • Off: TNS (parking lights) or headlight off control by auto light off system is not operated. • On: TNS (parking lights) or headlight off control by auto light off system is operated.	If the lights are turned off by the auto-light function (ignition is switched off), the value becomes On.	—
L_OFF_BS	Off/On	Note • Displays in the M-MDS but it does not operate.
OIL_P_SW	Off(Normal)/On(Low)	Note • Displays in the M-MDS but it does not operate.
OUT_CAR_TMP	°C, °F	Displays the ambient temperature value input from the PCM.	—	• 2N (CAN_L) • 2P (CAN_H)
P_BRAKE_SW	Off/On	Electric parking brake switch status having input from instrument cluster • Off: Electric parking brake switch is pressed. • On: Electric parking brake switch is pulled up.	—	• 2I (CAN_L) • 2K (CAN_H)
PNC_CS	Off/On	Panic signal input from rear body control module (RBCM) • Off: Panic control signal is not received. • On: Panic control signal is received.	—	• 2I (CAN_L) • 2K (CAN_H)
PNC_HD_CS_R	Off/On	Note • It is displayed, however, if an accessory part is installed, it cannot be used.
PNC_HN_CS_R	Off/On	Note • It is displayed, however, if an accessory part is installed, it cannot be used.
PTC_HEAT_CS	Off/On	Note • Displays in the M-MDS but it does not operate.
R_FOG_LMP^*8	Off/On	Rear fog light control signal • Off: Rear fog light is turned off. • On: Rear fog light is turned on.	—	—
R_FOG_SW^*8	Off/On	Rear fog light switch input signal from start stop unit • Off: Rear fog light switch is not in R.FOG position • On: Rear fog light switch is in R.FOG position	—	• 2I (CAN_L) • 2K (CAN_H)
RES_CS	Off/On	Note • It is displayed, however, if an accessory part is installed, it cannot be used.
RLS_FLT^*6	O.K./FAULT	Fail determination signal of auto light sensor/humidity sensor/rain sensor • O.K.: Rain sensor is normal. • FAULT: Rain sensor has a malfunction.	If normal, the value is O.K.. If abnormal, FAULT.	2G (LIN communication)
S_HT_CUT^*9	No_Request/Cut	Note • The FBCM controls the seat warmer output at an appropriate timing in consideration of the vehicle conditions such as power supply voltage decrease. • No_Request: Except below • Cut: When FBCM stops or lowers seat warmer output	—	—
SHIFT_L_POS	Between/P/R/N/D/S(2)/L(1)	Selector lever position signal from TCM • Between: Selector lever is between two positions. • P: Selector lever is in P position. • R: Selector lever is in R position. • N: Selector lever is in N position. • D: Selector lever is in D position. • S(2): Selector lever is in D position 2nd gear. • L(1): Selector lever is in D position 1st gear.	—	• 2L (CAN_L) • 2R (CAN_H)
TURN_L_L	Off/On	Turn light (LH) output signal • Off: Turn light (LH) is turned off. • On: Turn light (LH) is turned on.	—	—
TURN_L_R	Off/On	Turn light (RH) output signal • Off: Turn light (RH) is turned off. • On: Turn light (RH) is turned on.	—	—
TURN_SW	Off/Turn_R_On/Turn_L_On/Unknown	Turn switch signal input from start stop unit • Off: Turn switch is in OFF position. • Turn_R_On: Turn switch is in RH position. • Turn_L_On: Turn switch is in LH position. • Unknown: Turn switch position is not determined.	—	• 2I (CAN_L) • 2K (CAN_H)
VPWR_B	V	Displays front body control module (FBCM) power supply voltage	—	• 2A (Interior light power supply) • 3K (Power supply) • 3L (Power supply)
VSPD	KPH, MPH	Displays the vehicle speed signal from the PCM.	—	• 2N (CAN_L) • 2P (CAN_H)
WAS_FLUID_L^*10	Normal/Low/Reserved/Unknown	Washer fluid level • Normal: Washer fluid level is normal. • Low: Washer fluid level is low. • Reserved: — • Unknown: Washer fluid level is not determined.	—	2S (Washer level switch signal)
WAS_MT_RY_F	Off/On	Windshield washer motor relay operation signal • Off: Windshield washer motor relay is off. • On: Windshield washer motor relay is on.	—	3F (Windshield washer motor control)
WAS_MT_RY_R	Off/On	Rear washer motor relay operation signal • Off: Rear washer motor relay is off. • On: Rear washer motor relay is on.	—	3H (Rear window washer motor control)
WASHER_F	Off/On	Windshield washer switch input signal from start stop unit • Off: Windshield washer switch is off. • On: Windshield washer switch is on.	—	• 2I (CAN_L) • 2K (CAN_H)
WASHER_R	Off/On	Rear washer switch input signal from start stop unit • Off: Rear wiper and washer switch is not in rear washer position. • On: Rear wiper and washer switch is in rear washer position.	—	• 2I (CAN_L) • 2K (CAN_H)
WIP_CS_RLS^*6	Off/Single_Wipe/F_Wiper_LOW/F_Wiper_HI/Failure	Auto wiper input signal from auto light sensor/humidity sensor/rain sensor • Off: Wiper operation signal is not received from rain sensor. • Single_Wipe: Signal to operate wiper once is received from rain sensor. • F_Wiper_LOW: Signal to operate wiper at low speed is received from rain sensor. • F_Wiper_HI: Signal to operate wiper at high speed is received from rain sensor. • Failure: Communication with rain sensor is failed.	—	2G (LIN communication)
WIP_F	OFF/LOW/HI/INT / AUTO	Windshield wiper switch input signal from start stop unit • OFF: Windshield wiper switch is in OFF position. • LOW: Windshield wiper switch is in LO position. • HI: Windshield wiper switch is in HI position. • INT / AUTO: Windshield wiper switch is in INT or AUTO position.	—	• 2I (CAN_L) • 2K (CAN_H)
WIP_F_INT_L	%	Displays the windshield wiper intermittent interval time input signal from start stop unit.	—	• 2I (CAN_L) • 2K (CAN_H)
WIP_F_LOW	Off/On	• Off: Windshield wiper switch is not in LO position. • On: Windshield wiper switch is in LO position.	—	2Y (Windshield wiper low switch signal)
WIP_F_MST	Stop/Move	Windshield wiper stop position signal input • Stop: Windshield wipers stop at normal position • Move: Windshield wipers do not stop at normal position	If windshield wipers are operating, Move-Stop is repeated.	2AA (Autostop switch signal)
WIP_F_RY_HI	Off/On	Windshield wiper HI relay output signal • Off: Windshield wiper is not operating at HI. • On: Windshield wiper operating at HI.	—	• 3C (Windshield wiper motor (HI) control) • 3E (Windshield wiper motor (HI) control)
WIP_F_RY_LO	Off/On	Windshield wiper relay LO output signal • Off: Windshield wiper is not operating at LO. • On: Windshield wiper operating at LO.	—	• 3G (Windshield wiper motor (LOW) control) • 3I (Windshield wiper motor (LOW) control)
WIP_R	OFF/LOW/INT	Rear wiper operation condition input signal from start stop unit • OFF: Rear wiper switch is in OFF position. • LOW: Rear wiper switch is in ON position. • INT: Rear wiper switch is in INT position.	—	• 2I (CAN_L) • 2K (CAN_H)
WIP_R_RY	Off/On	Rear wiper relay drive signal • Off: Rear wiper motor is not operated. • On: Rear wiper motor is operated.	—	• 2I (CAN_L) • 2K (CAN_H)

PID

Unit/Operation

Data contents

Data read/use method

Module control terminal

ABK_CS_BG

Off/On

Note

• It is displayed, however, if an accessory part is installed, it cannot be used.

ABK_CS_KEY

Off/On

Note

• It is displayed, however, if an accessory part is installed, it cannot be used.

ABK_HD_CS_R

Off/On

Note

• It is displayed, however, if an accessory part is installed, it cannot be used.

ABK_HN_CS_R

Off/On

Note

• It is displayed, however, if an accessory part is installed, it cannot be used.

ABK_HN_KEY

Off/On

Keyless entry system horn answer-back signal input status

• Off: Keyless entry system horn answer-back signal is not received.

• On: Keyless entry system horn answer-back signal is received.

Keyless entry system horn answer-back request signal input from rear body control module (RBCM)

• 2I (CAN_L)

• 2K (CAN_H)

BAT_TMP^*1

°C, °F

Displays battery temperature (estimated).

Estimated battery temperature transmitted by LIN communication from current sensor

2E (LIN communication)

BG_ALARM_CS^*2

Off/On

Theft-deterrent system alarm signal input status

• Off: Hazard warning light flashing request signal is not received

• On: Hazard warning light flashing request signal is received

Theft-deterrent system alarm request signal input from rear body control module (RBCM)

Note

• Operates only if the ignition is switched off.

• 2I (CAN_L)

• 2K (CAN_H)

BLWR_MT_RY

Off/On

Blower motor relay output signal status

• Off: Blower relay is off.

• On: Blower relay is on.

—

2Z (Blower motor relay control)

BRAKE_SW

Off/On

Brake switch operation status

• Off: Brake switch (No. 2 signal) is off. (Brake pedal is depressed.)

• On: Brake switch (No. 2 signal) is on. (Brake pedal is not depressed.)

Brake switch signal status detected by PCM

• 2N (CAN_L)

• 2P (CAN_H)

BRK_F_L_SW

Normal/Low/Reserved/Unknown

Brake fluid level condition

• Normal: Brake fluid level is between MAX and MIN.

• Low: Brake fluid level is lower than MIN.

• Reserved: —

• Unknown: Brake fluid level is not determined.

—

2Q (Brake fluid level switch signal)

DCDC_CVT_ST^*3

Wake_Up/Bypass/Boost_1/Boost_2/Boost_3/Error/Default

DC-DC converter status

—

2H (LIN communication)

DCDC_VLT_O^*3

Displays DC-DC converter input voltage.

—

2H (LIN communication)

DEFOG_F_CS

Off/On

Front defogger operation request signal from climate control unit

• Off: Front defogger control signal is not received.

• On: Front defogger control signal is received.

—

• 2I (CAN_L)

• 2K (CAN_H)

DEFOG_R_CS

Off/On

Rear defogger operation request signal from climate control unit

• Off: Rear window defogger control signal is not received.

• On: Rear window defogger control signal is received.

—

• 2I (CAN_L)

• 2K (CAN_H)

ENG_C_TMP

°C, °F

Displays the engine coolant temperature value from the PCM.

—

• 2N (CAN_L)

• 2P (CAN_H)

ESS_ST

Off/On

Emergency signal system (ESS) operation condition

• Off: Emergency signal system (ESS) is not operated.

• On: Emergency signal system (ESS) is operated.

—

F_FOG_LMP^*4

Off/On

Front fog light control signal

• Off: Front fog light is turned off.

• On: Front fog light is turned on.

—

F_FOG_SW^*4

Off/On

Front fog light switch input signal from start stop unit

• Off: Front fog light switch F.FOG signal is not received.

• On: Front fog light switch F.FOG signal is received.

—

• 2I (CAN_L)

• 2K (CAN_H)

H/L

OFF/DRL/TNS/H/L_LOW/H/L_HI

Headlight control signal

• OFF: Headlight is turned off.

• DRL: Running light is turned on.

• TNS: TNS (parking lights) is turned on.

• H/L_LOW: Headlight (LO) is turned on.

• H/L_HI: Headlight (HI) is turned on.

—

H/L_CLN_RY^*5

Off/On

• Off: Headlight cleaner relay is off.

• On: Headlight cleaner relay is on.

—

1Q (Headlight cleaner relay)

H/L_CS_RLS^*6

Off/TNS_On/TNS+H/L_On/TNS+H/L_On_J

Headlight control input signal from auto light sensor/humidity sensor/rain sensor

• Off: TNS (parking lights) and headlight on request signal is not received from auto light sensor.

• TNS_On: TNS (parking lights) on signal is received from auto light sensor.

• TNS+H/L_On: TNS (parking lights) and headlight LO on signal is received from auto light sensor.

• TNS+H/L_On_J: —

—

2G (LIN communication)

H/L_HI

Off/On

Headlight HI beams

• Off: Headlight HI is turned off.

• On: Headlight HI is turned on.

—

H/L_SW_HI

Off/On

Light switch position (HI) condition via CAN signal from start stop unit

• Off: Light switch HI signal is not received.

• On: Light switch HI signal is received.

—

• 2I (CAN_L)

• 2K (CAN_H)

H/L_SW_LOW1

Off/On

Displays dimmer switch position of light switch sent from start stop unit via CAN signal

• Off: Other than dimmer switch LO position of light switch is received

• On: Dimmer switch LO position of light switch is received

Verify if the monitor value switches when the dimmer switch of the light switch is switched between LO and HI positions. If the dimmer switch operation and monitor values do not match, inspect the start stop unit or CAN communication.

• 2I (CAN_L)

• 2K (CAN_H)

H/L_SW_OFF

Off/On

Light switch position (OFF) condition via CAN signal from start stop unit

• Off: Light switch OFF signal is not received.

• On: Light switch OFF signal is received.

—

• 2I (CAN_L)

• 2K (CAN_H)

H/L_SW_PASS

Off/On

Light switch position (PASS) condition via CAN signal from start stop unit

• Off: Light switch FLASH-TO-PASS signal is not received.

• On: Light switch FLASH-TO-PASS signal is received.

—

• 2I (CAN_L)

• 2K (CAN_H)

H/L_SW_TNS

Off/On

Light switch position (TNS (parking lights)) status via CAN signal from start stop unit

• Off: Light switch TNS (parking lights) signal is not received.

• On: Light switch TNS (parking lights) signal is received.

—

• 2I (CAN_L)

• 2K (CAN_H)

H/L_TNS

Off/On

Light switch (TNS (parking lights)) output signal

• Off: TNS (parking lights) is turned off.

• On: TNS (parking lights) is turned on.

—

HAZARD_LMP

Off/On

Hazard light output signal

• Off: Hazard light is turned off.

• On: Hazard light is turned on.

—

HAZARD_SW

Off/On/Unknown

Hazard switch input signal from start stop unit

• Off: Hazard warning switch is off.

• On: Hazard warning switch is on.

• Unknown: Hazard warning switch on/off is not determined.

—

• 2I (CAN_L)

• 2K (CAN_H)

HBC_CS^*7

Off/On/Invalid

• Off: High beam control (HBC) system signal is not received.

• On: High beam control (HBC) system signal is received.

• Invalid: High beam control (HBC) system signal has error.

—

• 2I (CAN_L)

• 2K (CAN_H)

HBC_ST^*7

Off/On

• Off: High beam control (HBC) system is not operated.

• On: High beam control (HBC) system is operated.

—

• 2I (CAN_L)

• 2K (CAN_H)

HEAT_CS_R

Off/On

Note

• It is displayed, however, if an accessory part is installed, it cannot be used.

IG_ST

Off/On

Ignition switch status

• Off: IG1 is off.

• On: IG1 is on.

—

L_OFF_AUTO^*6

Off/On

Operation status of lights off function by auto-light function

• Off: TNS (parking lights) or headlight off control by auto light off system is not operated.

• On: TNS (parking lights) or headlight off control by auto light off system is operated.

If the lights are turned off by the auto-light function (ignition is switched off), the value becomes On.

—

L_OFF_BS

Off/On

Note

• Displays in the M-MDS but it does not operate.

OIL_P_SW

Off(Normal)/On(Low)

Note

• Displays in the M-MDS but it does not operate.

OUT_CAR_TMP

°C, °F

Displays the ambient temperature value input from the PCM.

—

• 2N (CAN_L)

• 2P (CAN_H)

P_BRAKE_SW

Off/On

Electric parking brake switch status having input from instrument cluster

• Off: Electric parking brake switch is pressed.

• On: Electric parking brake switch is pulled up.

—

• 2I (CAN_L)

• 2K (CAN_H)

PNC_CS

Off/On

Panic signal input from rear body control module (RBCM)

• Off: Panic control signal is not received.

• On: Panic control signal is received.

—

• 2I (CAN_L)

• 2K (CAN_H)

PNC_HD_CS_R

Off/On

Note

• It is displayed, however, if an accessory part is installed, it cannot be used.

PNC_HN_CS_R

Off/On

Note

• It is displayed, however, if an accessory part is installed, it cannot be used.

PTC_HEAT_CS

Off/On

Note

• Displays in the M-MDS but it does not operate.

R_FOG_LMP^*8

Off/On

Rear fog light control signal

• Off: Rear fog light is turned off.

• On: Rear fog light is turned on.

—

R_FOG_SW^*8

Off/On

Rear fog light switch input signal from start stop unit

• Off: Rear fog light switch is not in R.FOG position

• On: Rear fog light switch is in R.FOG position

—

• 2I (CAN_L)

• 2K (CAN_H)

RES_CS

Off/On

Note

• It is displayed, however, if an accessory part is installed, it cannot be used.

RLS_FLT^*6

O.K./FAULT

Fail determination signal of auto light sensor/humidity sensor/rain sensor

• O.K.: Rain sensor is normal.

• FAULT: Rain sensor has a malfunction.

If normal, the value is O.K.. If abnormal, FAULT.

2G (LIN communication)

S_HT_CUT^*9

No_Request/Cut

Note

• The FBCM controls the seat warmer output at an appropriate timing in consideration of the vehicle conditions such as power supply voltage decrease.

• No_Request: Except below

• Cut: When FBCM stops or lowers seat warmer output

—

SHIFT_L_POS

Between/P/R/N/D/S(2)/L(1)

Selector lever position signal from TCM

• Between: Selector lever is between two positions.

• P: Selector lever is in P position.

• R: Selector lever is in R position.

• N: Selector lever is in N position.

• D: Selector lever is in D position.

• S(2): Selector lever is in D position 2nd gear.

• L(1): Selector lever is in D position 1st gear.

—

• 2L (CAN_L)

• 2R (CAN_H)

TURN_L_L

Off/On

Turn light (LH) output signal

• Off: Turn light (LH) is turned off.

• On: Turn light (LH) is turned on.

—

TURN_L_R

Off/On

Turn light (RH) output signal

• Off: Turn light (RH) is turned off.

• On: Turn light (RH) is turned on.

—

TURN_SW

Off/Turn_R_On/Turn_L_On/Unknown

Turn switch signal input from start stop unit

• Off: Turn switch is in OFF position.

• Turn_R_On: Turn switch is in RH position.

• Turn_L_On: Turn switch is in LH position.

• Unknown: Turn switch position is not determined.

—

• 2I (CAN_L)

• 2K (CAN_H)

VPWR_B

Displays front body control module (FBCM) power supply voltage

—

• 2A (Interior light power supply)

• 3K (Power supply)

• 3L (Power supply)

VSPD

KPH, MPH

Displays the vehicle speed signal from the PCM.

—

• 2N (CAN_L)

• 2P (CAN_H)

WAS_FLUID_L^*10

Normal/Low/Reserved/Unknown

Washer fluid level

• Normal: Washer fluid level is normal.

• Low: Washer fluid level is low.

• Reserved: —

• Unknown: Washer fluid level is not determined.

—

2S (Washer level switch signal)

WAS_MT_RY_F

Off/On

Windshield washer motor relay operation signal

• Off: Windshield washer motor relay is off.

• On: Windshield washer motor relay is on.

—

3F (Windshield washer motor control)

WAS_MT_RY_R

Off/On

Rear washer motor relay operation signal

• Off: Rear washer motor relay is off.

• On: Rear washer motor relay is on.

—

3H (Rear window washer motor control)

WASHER_F

Off/On

Windshield washer switch input signal from start stop unit

• Off: Windshield washer switch is off.

• On: Windshield washer switch is on.

—

• 2I (CAN_L)

• 2K (CAN_H)

WASHER_R

Off/On

Rear washer switch input signal from start stop unit

• Off: Rear wiper and washer switch is not in rear washer position.

• On: Rear wiper and washer switch is in rear washer position.

—

• 2I (CAN_L)

• 2K (CAN_H)

WIP_CS_RLS^*6

Off/Single_Wipe/F_Wiper_LOW/F_Wiper_HI/Failure

Auto wiper input signal from auto light sensor/humidity sensor/rain sensor

• Off: Wiper operation signal is not received from rain sensor.

• Single_Wipe: Signal to operate wiper once is received from rain sensor.

• F_Wiper_LOW: Signal to operate wiper at low speed is received from rain sensor.

• F_Wiper_HI: Signal to operate wiper at high speed is received from rain sensor.

• Failure: Communication with rain sensor is failed.

—

2G (LIN communication)

WIP_F

OFF/LOW/HI/INT / AUTO

Windshield wiper switch input signal from start stop unit

• OFF: Windshield wiper switch is in OFF position.

• LOW: Windshield wiper switch is in LO position.

• HI: Windshield wiper switch is in HI position.

• INT / AUTO: Windshield wiper switch is in INT or AUTO position.

—

• 2I (CAN_L)

• 2K (CAN_H)

WIP_F_INT_L

Displays the windshield wiper intermittent interval time input signal from start stop unit.

—

• 2I (CAN_L)

• 2K (CAN_H)

WIP_F_LOW

Off/On

• Off: Windshield wiper switch is not in LO position.

• On: Windshield wiper switch is in LO position.

—

2Y (Windshield wiper low switch signal)

WIP_F_MST

Stop/Move

Windshield wiper stop position signal input

• Stop: Windshield wipers stop at normal position

• Move: Windshield wipers do not stop at normal position

If windshield wipers are operating, Move-Stop is repeated.

2AA (Autostop switch signal)

WIP_F_RY_HI

Off/On

Windshield wiper HI relay output signal

• Off: Windshield wiper is not operating at HI.

• On: Windshield wiper operating at HI.

—

• 3C (Windshield wiper motor (HI) control)

• 3E (Windshield wiper motor (HI) control)

WIP_F_RY_LO

Off/On

Windshield wiper relay LO output signal

• Off: Windshield wiper is not operating at LO.

• On: Windshield wiper operating at LO.

—

• 3G (Windshield wiper motor (LOW) control)

• 3I (Windshield wiper motor (LOW) control)

WIP_R

OFF/LOW/INT

Rear wiper operation condition input signal from start stop unit

• OFF: Rear wiper switch is in OFF position.

• LOW: Rear wiper switch is in ON position.

• INT: Rear wiper switch is in INT position.

—

• 2I (CAN_L)

• 2K (CAN_H)

WIP_R_RY

Off/On

Rear wiper relay drive signal

• Off: Rear wiper motor is not operated.

• On: Rear wiper motor is operated.

—

• 2I (CAN_L)

• 2K (CAN_H)