PID/DATA MONITOR INSPECTION (i-stop) [SKYACTIV-G 2.5T]

id1102b4000100

Note
•  PIDs related to i-stop can be displayed in a list using the M-MDS data monitor diagnostic function.
•  If the engine is stopped by the i-stop control while the following data monitor items on the M-MDS are being viewed, the data monitor items may no longer be displayed.
?  BRAKE_SW
?  BRK_F_P_C
?  LON_ACCL_C
?  WSPD_SEN_LF
?  WSPD_SEN_RF
?  WSPD_SEN_LR
?  WSPD_SEN_RR

1.  Connect the M-MDS to the DLC-2.

2.  After vehicle identification is completed, select the following from the M-MDS initial screen.

(1)  [Data logger]
(2)  [Powertrain]
(3)  [i-stop]

3.  Select the applicable item from the PID/DATA Monitor Table.

4.  Verify the monitored value according to the directions on the screen.

PID/DATA Monitor Table

Module

Item (definition)

Unit/Condition

Page
PCM
APP
%
(See PCM INSPECTION [SKYACTIV-G 2.5T].)
APP1
%
APP2
%
BARO
KPa {MPa}, mBar {Bar}, psi, in H20
BATT_CUR
A
BATT_RES
Not applicable
BATT_SOC
%
BATT_TEMP
°C, °F
BATT_V
V
BBP
KPa {MPa}, mBar {Bar}, psi, in H20
BFP
KPa {MPa}, mBar {Bar}, psi, in H20
BOO
High/Low
BPA
High/Low
ECT
°C, °F
IAT
°C, °F
I-Stop_OFF
Off/On
I-Stop_TRD
Off/On
I-Stop_VSP
Off/On
I-Stop_VST
Off/On
M_GEAR
Neutral/1st gear/2nd gear/3rd gear/4th gear/5th gear/6th gear/Reverse/Undefined/Auto/In_Progress/YSF/Error
VPWR
V
DSC HU/CM
BRAKE_SW
Off/On
(See PID/DATA MONITOR TABLE [DSC HU/CM].)
BRK_F_P_C
KPa {MPa}, mBar {Bar}, psi, in H20
LON_ACCL_C
G
WSPD_SEN_LF
KPH, MPH
WSPD_SEN_LR
KPH, MPH
WSPD_SEN_RF
KPH, MPH
WSPD_SEN_RR
KPH, MPH
TCM
I-Stop_EST
Off/On
(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [TCM (GW6A-EL, GW6AX-EL)].)
TFT
°C, °F
TR
P/SHIFT_DOWN/SHIFT_UP/M/D/N/R
EPS control module
STR_AB_EST
°(deg)
(See PID/DATA MONITOR TABLE [ELECTRIC POWER STEERING (EPS)].)
STR_ROT_SPD
°/s
STR_TRQ_S_M
Nm
Climate control unit
STOP_ST
Available/Not Available/Error
(See PID/DATA MONITOR TABLE [CLIMATE CONTROL UNIT (FULL-AUTO AIR CONDITIONER)].)
SAS control module
SEAT_B_D
Unbuckled/Buckled
(See PID/DATA MONITOR TABLE [SAS CONTROL MODULE].)
Rear body control module (RBCM)
DOOR_ALL
Close/OPEN
(See PID/DATA MONITOR TABLE [REAR BODY CONTROL MODULE (RBCM)].)
DOOR_D
Close/OPEN
HOOD
Close/OPEN
TRUNK
Close/OPEN
Start stop unit
RELAY_ACC
Off/On
(See PID/DATA MONITOR TABLE [START STOP UNIT].)
RELAY_IG1
Off/On
RELAY_IG2
Off/On
SSB_1
Off/On
SSB_2
Off/On
VPWR_ACC
V
VPWR_B1
V
VPWR_IG1
V
DC-DC converter (i-ELOOP)*1
BYPS_STAT
Bypass Off/Bypass On/Bypass Off fault/Bypass On fault
(See PID/DATA MONITOR INSPECTION [i-ELOOP].)
DCDC_IN_V
V

*1   :Vehicles with i-ELOOP