PERSONALIZATION FEATURES

id120000000000

Caution

• The personalization feature may not be set correctly if [Not equipped] is selected in the setting displayed on the M-MDS. Do not select [Not equipped] in the setting displayed on the M-MDS.

Note

• Settings of some personalization features cannot be switched depending on the vehicle specification.

• The following systems can be personalized.

• When performing a personalization setting, refer to the referenced section for the detailed setting procedure.

DOOR AND LIFTGATE

Hands-free liftgate

Personalization features	Setting contents	Setting procedure
The hands-free liftgate can be switched ON/OFF.	ON / OFF	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Glass/Windows/Mirrors

Rear window defogger

Personalization features	Setting contents	Setting procedure
Rear window defogger operation time can be changed.	15 minutes / Continuous^*1	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 The operation may stop in 15 minutes due to the effect of the outside temperature even if the operation time of the rear window defogger has been changed to Continuous.

Security And Locks

Advanced keyless entry system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features	Setting contents	Setting procedure
The advanced keyless entry system and push button start system functions can be disabled.	Enable / Disable	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
The out-of-area (reception area) type auto lock function can be set.	Off / On	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation start time of the auto re-lock function can be changed.	30 seconds / 60 seconds / 90 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The keyless beeper volume can be adjusted.	Off / Low / Medium / High	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the door lock system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Keyless entry system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features	Setting contents	Setting procedure
The keyless entry system and push button start system functions can be disabled.	Enable / Disable	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation start time of the auto re-lock function can be changed.	30 seconds / 60 seconds / 90 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the door lock system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Power door lock system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features	Setting contents	Setting procedure
Auto door lock function can be changed.	Lock: When Driving, Unlock: In Park / Lock: Out of Park, Unlock: In Park / Lock: Shifting Out of Park / Lock: When Driving, Unlock: IGN Off / Lock: When Driving / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Auto door lock function can be changed.		Door lock switch is used for the setting. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the door lock system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Power saving function (with remote transmitter type B)

Personalization features	Setting contents	Setting procedure
The power saving function can be set.	OFF / ON	Remote transmitter button is used for the setting. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

Lighting Systems

Auto light system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features	Setting contents	Setting procedure
Auto light sensor sensitivity can be changed.	Light / Medium Light / Medium / Medium Dark / Dark	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Turn light system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features	Setting contents	Setting procedure
The operation of the three-flash turn signal function can be disabled.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The volume of the turn and hazard indicator alarm can be changed.	High / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Running Light System (General (L.H.D. R.H.D.), Australian Specs.)

Personalization features	Setting contents	Setting procedure
The running light system function can be set.	On (Running light illumination) / Off (Running light non-illumination)	Light switch is used for the setting. (See LIGHTING SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Coming home light

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features	Setting contents	Setting procedure
The coming home light operation time can be switched.	Off / 30 seconds / 60 seconds / 90 seconds / 120 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The coming home light operation time can be switched.	Off / 30 seconds / 60 seconds / 90 seconds / 120 seconds	M-MDS is used. (See LIGHTING SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Leaving home light

Note

• There are three methods for personalizing the leaving home light system: Using the M-MDS, using the center display, and using the light switch.

Personalization features	Setting contents	Setting procedure
The leaving home light can be switched between operable and inoperable.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
	On / Off	M-MDS is used. (See LIGHTING SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Interior light control system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features	Setting contents	Setting procedure
• The front/rear map light illumination time after any door is opened can be changed. • The cargo compartment light illumination time after the trunk lid is opened can be changed.	60 minutes / 30 minutes / 10 minutes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
	30 minutes. / 60 minutes. / 10 minutes.	M-MDS is used. (See LIGHTING SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
The front/rear map light illumination time after all the doors are closed can be changed.	60 seconds / 30 seconds / 15 seconds / 7.5 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
	15 seconds. / 7.5 seconds. / 30 seconds. / 60 seconds.	M-MDS is used. (See LIGHTING SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
The ambient light brightness can be changed when the TNS (parking lights) are turned on.	Bright / Medium / Dark / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Wiper/Washer System

Auto wiper system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features	Setting contents	Setting procedure
The auto wiper function can be disabled.	On / Off^*1	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The auto wiper function can be disabled.	Off (Intermittent) / On (Rain Sensing)	M-MDS is used. (See WIPER/WASHER PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :When the system is set to [Off] and the wiper switch is in the AUTO position, the wipers operate intermittently.

Entertainment

Language

Personalization features	Setting contents	Setting procedure
The display language can be changed.	Depends on market	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Fuel economy monitor

Personalization features	Setting contents	Setting procedure
The ending screen of the fuel monitor can be switched between display/non-display.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The function which synchronizes the reset of the fuel reset and trip meters can be switched between on/off.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Instrumentation/Driver Info.

Turn and hazard indicator alarm

Personalization features	Setting contents	Setting procedure
The volume of the turn and hazard indicator alarm can be changed.	High / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Lights-on reminder warning alarm

Personalization features	Setting contents	Setting procedure
The volume of the lights-on reminder warning alarm can be changed.	High / Low / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
	OFF / Low / High	Center display is used for the setting. (See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

Temperature

Personalization features	Setting contents	Setting procedure
The temperature unit can be changed.^*1	°F /°C^*2	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :When the ambient temperature display is switched, the set A/C cabin temperature display is also changed.

*2 :The initial value differs depending on the market.

Distance

Personalization features	Setting contents	Setting procedure
The distance unit can be changed.	mi / Km	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Active driving display

Personalization features	Setting contents	Setting procedure
Setting can be changed so that the active driving display is not displayed.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The display height (up/down position) can be changed.	13 steps up / down from initial setting (total: 27steps)	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The method for adjusting the display brightness (automatically/manually) can be changed.	AUTO / MANUAL	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The standard brightness with the automatic brightness adjustment can be changed.	2 steps up / down from initial setting (total: 5 steps)	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The standard brightness with the manual brightness adjustment can be changed.	20 steps up / down from initial setting (total: 41 steps)	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The tilt of the displayed image can be adjusted.	3 steps up / down from initial setting (total: 7 steps)	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Setting can be changed so that the navigation system guidance is not displayed.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Parking sensor system

Personalization features	Setting contents	Setting procedure
The parking sensor information can be displayed on the center display.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

i-ACTIVSENSE

Adaptive front lighting system (AFS)

Personalization features	Setting contents	Setting procedure
The adaptive front lighting system (AFS) can be switched between operable and inoperable.	OFF / ON	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Adaptive LED headlight system

Personalization features	Setting contents	Setting procedure
The adaptive LED headlights function can be changed.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

High beam control (HBC) system

Personalization features	Setting contents	Setting procedure
The high beam control (HBC) system can be switched between operable and inoperable.	OFF / ON	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Distance Recognition Support System (DRSS)

Personalization features	Setting contents	Setting procedure
The operation of distance recognition support system (DRSS) can be turned off.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation distance for the alert function can be changed.	Far / Medium / Near	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the distance recognition support system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Advanced smart city brake support (Advanced SCBS)/Smart City Brake Support (SCBS)

Personalization features	Setting contents	Setting procedure
The Smart City Brake Support (SCBS)/Advanced Smart City Brake Support (Advanced SCBS) can be switched between operable and inoperable.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The distance at which the collision warning activates can be changed.	Far / Medium / Near	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The volume of Smart City Brake Support (SCBS)/Advanced Smart City Brake Support (Advanced SCBS) warning alarm can be changed.	High / Low / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Smart Brake Support (SBS)

Personalization features	Setting contents	Setting procedure
The operation of Smart Brake Support (SBS) can be turned off.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The distance at which the collision warning activates can be changed.	Far / Medium / Near	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The volume of Smart Brake Support (SBS) warning alarm can be changed.	High / Low / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the smart brake support (SBS) system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Smart city brake support [Forward] (SCBS F)

Personalization features	Setting contents	Setting procedure
Smart City Brake Support [Forward] (SCBS F) can be turned off.	ON / OFF	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Smart city brake support [Reverse] (SCBS R)

Personalization features	Setting contents	Setting procedure
Smart City Brake Support [Reverse] (SCBS R) can be turned off.	ON / OFF	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Blind Spot Monitoring (BSM) System

Personalization features	Setting contents	Setting procedure
The system can be changed so that Blind Spot Monitoring (BSM) does not operate.	On / Off	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The volume of the blind spot monitoring (BSM) warning alarm can be changed.	OFF / Low / High	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
	High / Low / OFF	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Lane-keep Assist System / Lane Departure Warning System (LDWS)

Personalization features		Setting contents	Setting procedure
The function of lane departure warning system (LDWS) / lane-keep assist system can be switched.		OFF / LKA / LDWS	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation of the lane-keep assist system warning (steering wheel vibration) can be turned off.		ON / OFF	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Intervention is ON	The operation timing of steering wheel operation assist can be changed.	Early / Late	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
	The operation sensitivity of steering wheel operation assist can be changed.	High / Med / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
	The operation of the lane-keep assist system warning can be turned off.	ON / OFF	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Intervention is OFF	The operation timing of lane-keep assist system warning can be changed.	Adaptive / Early / Medium / Late	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Intervention is OFF	The warning operation sensitivity of lane-keep assist system warning can be changed.	High / Med / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The type of the lane-keep assist system warning (type of sound or vibration) can be changed.		Vibration / Rumble Strip / Beep	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The strength of steering wheel vibration can be changed.		High / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The volume of the lane departure warning sound (beep) can be changed.		High / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The volume of the lane departure warning sound (rumble strip) can be changed.		High / Mid / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Driver Attention Alert System

Personalization features	Setting contents	Setting procedure
The system can be changed so that driver attention alert does not operate.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

360°view monitor system

Personalization features	Setting contents	Setting procedure
Automatically displays the 360°view monitor system when the ignition is switched ON (engine on).	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The predicted vehicle track display can be switched between display/non-display.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The display of the top view/front view while driving the vehicle in the forward direction after reversing can be switched between display/non-display.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The settings for the 360° view monitor system can be reset to the initial values.	No / Yes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Traffic sign recognition system (TSR)

Personalization features	Setting contents	Setting procedure
The operation of traffic sign recognition system (TSR) can be turned off.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The activation timing for the excessive speed warning can be changed.	Off / Visual / Audio & Visual	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The activation timing for the excessive speed warning can be changed.	+0 / +5 / +10	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)